脱粒机使用后的处理要点 脱粒机在使用过程中难免有不同零部件等部位的磨损

脱粒机使用后的处理要点 脱粒机在使用过程中难免有不同零部件等部位的磨损，因此脱粒机在使用过后一定要做好全方位的检查。以避免在次使用时造成不必要的麻烦。具体工作实施可按照以下说明进行： （1）脱粒结束后，应仔细清除机内的尘污和杂物；对在使用过程中油漆脱落的地方，按要求重新涂上油漆。 （2）脱焊及裂缝的部位要焊修。 （3）安装纹杆注意，应让小头朝向喂入方向，相邻两根纹杆的纹路方向应相反，以防谷物移到滚筒的一端，产生负荷不均现象。 （4）按规定扭矩拧紧纹杆螺栓。一般分3－4次拧紧；检查每根纹杆螺栓是否都有锁紧螺母，因为脱粒机作业时，滚微高速运转，螺母易松动，且纹杆质量必须符合要求，不能用其它螺栓代替。 （5）脱粒机滚筒修理后应做静平衡调试，直到调试平衡为止。 （6）检查脱粒机护板罩是否牢固，破损的要更换。 （7）维修完备，向各注油点、润滑点加注足量的润滑油，各调节螺钉的螺纹上也要涂油防锈；将脱粒机放在干燥通风的棚内，注意不要在脱粒机上面放杂物以防变形。

結果 (英文) 1:

Thresher thresher elements disposal after use is inevitable in the course of different parts and other parts of the wear and tear, so after use thresher sure to do a full range of checks. When used at times to avoid unnecessary trouble. Implementation of the specific work carried out in accordance with the following instructions: (1) After threshing, you should carefully remove dirt and dust inside the debris; against peeling paint in the course of the place, as required to re-coated paint. (2) sealing off and crack the parts to be welded repair. (3) Installation pattern rod attention should be allowed to head towards the feed direction, the adjacent two lines should be directed to the opposite pole of the lines,Moved to one end of the drum to prevent the grain, resulting in uneven load phenomenon. (4) to the specified torque rod bolt tightening pattern. Generally 3-4 times tighten; checking whether each pattern has a rod bolt lock nut, because thresher operation, high speed micro-roll, easy to loose nuts and grain quality must meet the requirements lever can not be replaced by other bolts. (5) thresher drum repairs should be done after the static balance debugging, until the debugger balance so far. (6) Check the thresher guard cover is solid, damaged should be replaced. (7) Repair complete, each oiling point, raise a sufficient amount of lubrication points lubricant on the threads of the adjusting screw should be oiled rust;The thresher in a dry airy shed, be careful not to put debris in the thresher above to prevent deformation.

結果 (英文) 2:

Abrasion treatment of threshing machine after use will inevitably be different parts and other parts in the use process, so check the threshing machine must do a full range in use after the. In order to avoid unnecessary trouble in use. The implementation of specific work can be carried out according to the following: (1) after threshing, should be carefully remove dirt and debris inside the machine; the paint off place in the use of the process, according to the requirements of the new paint. (2) the unsoldering and fracture site to repair welding. (3) installation thread rod attention, should let the head toward the feeding direction, texture direction of two adjacent rasp bars should be opposite,In order to prevent grain moved to one side of the cylinder, the load imbalance phenomenon. (4) according to the prescribed tightening torque thread rod bolt. Generally 3 - 4 tightening; check each thread rod bolts are locking nut, because threshing machine operation, the micro high-speed operation, the nut is easy to loose, and the thread rod quality must meet the requirements, can not be replaced by other bolt. (5) the thresher drum repair should be done after the commissioning of static balance, until debug balance so far. (6) check the threshing machine shield cover is firmly, damaged should be replaced. (7) repair is complete, lubricating oil to each lubricating point, add enough lubrication points, screw the adjustment screw should also be oiled;The threshing machine placed in dry and ventilated sheds, careful not to put debris in the threshing machine to prevent deformation.

結果 (英文) 3:

Sheller points after Sheller in use will inevitably be different parts and other parts from being damaged, thresher after use be sure to do a full range of checks. When used to avoid causing unnecessary trouble. Specific implementation in accordance with the following instructions: (1) after the end of the threshing, machine dust dirt and debris should be cleared carefully; in the process of peeling paint, coating paint again, as required. (2) removal of welding and parts of welding repair of cracks. (3) installing sheath note, should be allowed to head towards the feeding direction, two adjacent lines pole lines should be the opposite,In case of grain moved to one end of the drum, resulting in uneven loads. (4) on the required bolt torque tightening pattern rod. General 3-4 tighten; check that each grain pole bolt lock nut, because when the threshers jobs, rolled micro-high speed operation, nuts are loose, and grain quality must meet the requirement, you can't use the other bolts in place. (5) static balance adjustment should be done after the thresher drum repair until the debugging until the balance. (6) check the thresher solid shields cover, broken to be replaced. (7) maintenance is complete, to the oil injection point raises plenty of lubricant, lubrication points, the adjustment screw oil on the threads of rust;Thresher in a dry ventilated sheds, attention should not be above the thresher debris to prevent deformation.