模具雕刻机的快速雕刻技巧要实现快速雕刻(当然是保质保量的可以尝试下面的

模具雕刻机的快速雕刻技巧
要实现快速雕刻(当然是保质保量的可以尝试下面的操作下）：

首先考虑一下你否必需使用锥性刀鼻子， 被雕刻物所受到下压力如果很大。如果雕刻机钻石刀头在雕刻过程中移动时压力过大，工具正面的压力就会造成被雕刻物的移动。如果使用了不正确的钻石刀，也会导致同样的问题。一个90或100度的钻石刀会深入资料雕刻，而使得材料在被雕刻过程中移动。

雕刻机钳子或卡头的磨损情况也会导致被雕刻物的错位。

钳子或卡头如果过紧，检查雕刻所选用的钳子或卡头是否用错了同时。刀头接触被雕刻物的瞬间也会导致被雕刻物的弹出。

而它又是铁制的因此容易对被雕刻物造成损伤或使其在雕刻过程中滑落，由于雕刻机上经常配有多功能的钳子或卡头。使用模具雕刻机时应特别的注意。那么选用一些橡胶帽或者橡胶管子用于被雕刻物的固定会有帮助。

可以将转贴胶带贴在被雕刻物的反面， 对于雕刻塑料图案。再将贴有胶带的一面喷上液体喷胶，之后将其贴在一个可以作废的外表上，这样可以防止使用双面胶，而留下难以清洁的外表。因为转贴胶带容易剥离和清理。使用专门的有雕刻的带子，这种带子一侧比另一侧的粘性强，因此图版可以随意移动或更换了5.对于那些不规则形状的被雕刻物，外表上看起来已经被固定的很紧了当受到下压力时也会前后晃动。这时，可以试着在物体下面垫上些废料以增加摩擦。另外就是保管物品自带的包装，虽然物体是不规则形状的但是其自身所带的包装可能是很规则的且易于被固定，再加上一小条带子，不规则形状的物体就很容易被固定了或者试用工具固定其规则的部位，而舍弃其不规则的部位。

結果 (英文) 1:

Rapid mold engraving machine engraving techniquesTo achieve fast carving (quality and quantity, of course you can try the following actions): First of all, consider whether you need to use nose cone knife, carved by pressure if the very big. If engraving machine diamond tool moves too much pressure in the engraving process, tool pressure will result in being carved on the front of the movement. If you are using an incorrect diamond knife, can also cause the same problem. A 90 or 100 degrees, carved diamond blade depth information, and materials move in the carving process.Engraving machine pliers or head wear will result in dislocation of the carvings.Pliers or Chuck if too tight, check whether the carving the use of pliers or Chuck uses the wrong at the same time. Cutter head in contact with carvings of the moment can also cause pop-up by carvings.And it is made of iron and therefore easily carved material damage or make it slip during the carving process, as engraving machines are often equipped with multifunctional pliers or Chuck. Using mold engraving machine should pay special attention. Then use some rubber cap or rubber tubes for the carvings will help fix.可以将转贴胶带贴在被雕刻物的反面， 对于雕刻塑料图案。再将贴有胶带的一面喷上液体喷胶，之后将其贴在一个可以作废的外表上，这样可以防止使用双面胶，而留下难以清洁的外表。因为转贴胶带容易剥离和清理。使用专门的有雕刻的带子，这种带子一侧比另一侧的粘性强，因此图版可以随意移动或更换了5.对于那些不规则形状的被雕刻物，外表上看起来已经被固定的很紧了当受到下压力时也会前后晃动。这时，可以试着在物体下面垫上些废料以增加摩擦。另外就是保管物品自带的包装，虽然物体是不规则形状的但是其自身所带的包装可能是很规则的且易于被固定，再加上一小条带子，不规则形状的物体就很容易被固定了或者试用工具固定其规则的部位，而舍弃其不规则的部位。

結果 (英文) 3:

Mould engraving machine fast carving skills
to realize rapid carving (is, of course, guarantee both quality and quantity can try the following operation:

consider first whether you must use conical cutter nose, carved by pressure, if large. If the engraving machine diamond cutter head in the process of moving when the pressure is too large, the pressure will cause the tool to move the sculpture. If you use the wrong diamond knife, it will also lead to the same problem. A 90 - or 100 - degree diamond knife will be carved in depth, and the material is moved in the process of being carved. Wear, engraving machine pliers or a clamping head can also lead to be carving misalignment.

the pliers head or card if too tight, check the carving the pliers or card head is wrong at the same time. The moment of contact with the head of the knife can also lead to the ejection of the carved object.

and it is iron so easily to carved objects cause damage or the slide in the carving process, due to the engraving machine often equipped with multifunctional pliers or a clamping head. Special attention should be paid to the use of mould engraving machine. So the use of some rubber cap or rubber pipe for the sculpture of the fixed will help.

can be reposted tape affixed to the side to be carving, carving patterns for plastics. The liquid glue affixed with adhesive tape side spray,After that, it can be affixed to an invalid appearance, which can prevent the use of double-sided adhesive, and leave it difficult to clean the surface. Because the tape stripping and cleaning easier. Using a special carved tape, the tape side than on the other side of the viscous strong, so the plate can move freely or replaced. For those with irregular shapes are carvings, appearance seems to have been fixed tight when subjected to pressure will swing back and forth. At this time, you can try to pad some waste on the object to increase friction. In addition to the custody of the package comes with,Although the object is irregular shape but its own packaging may be very regular and easy to be fixed, plus a small tape, irregular shaped objects can easily be fixed or probation tools to fix the part of the rules, and to abandon its irregular parts.