C13B轻型护卫舰局域网系统出厂验收大纲共 10张桂林利达通讯工程有限

C13B轻型护卫舰
局域网系统


出厂验收大纲






共 10张





桂林利达通讯工程有限责任公司

2014年2月







C13B轻型护卫舰
局域网系统


出厂验收大纲













拟 制：
审 核：
会 签：
会 签：
会 签：
批 准：


文档修改记录
版本号 修改内容描述 修改人 日期 备注
























目次
1 前言 1
2 系统主要设备组成 1
3 调试用仪器仪表 1
4 系统技术指标 1
5 试验方法 4
5.1 外观质量 4
5.2 设备尺寸 4
5.3 安全性 4
5.3.1 电气安装要求 4
5.3.2 绝缘电阻 4
5.4 工作电源电压波动 5
5.5 系统功耗 5
5.6 功能测试 5
5.6.1 局域网内部数据交互与通信 5
5.6.2 局域网接入互联网功能 5
5.7 参数测试 6
5.7.1 岸基接线盒 6
5.7.2 网络接座 6
5.7.3 千兆路由器 6
5.7.4 千兆交换机 7
5.7.5 网络服务器 7
5.7.6 UPS电源 8
附录1 10
A.1 系统示意图 10


1 前言
本试验手册根据《C13B轻型护卫舰局域网系统设备技术规格书》而制定，作为设备检验的依据。
2 系统主要设备组成
表1、受试设备组成
序号 名 称 及 型 号 数量 单位 备注
1 网络机柜 7寸液晶显示器 1 台
2 光电转换器 1 台 单模
3 千兆路由器 1 台
4 网络服务器 1 台
5 48口千兆交换机 1 台
6 AMP超五类48口配线架 1 台
7 3000VA UPS 1 台
8 折叠型鼠标键盘 1 套
9 AMP网络插座 30 个
10 AMP跳线 30 个
11 岸基接线盒 2 个

3 调试用仪器仪表
表2、调试使用仪器仪表
名称 型号 仪器编号 有效日期
数字万用表 MY-65 260602-1902
兆欧表 ZC25－3 260601-0804
电阻测试仪 AT510PRO 360102-0801
游标卡尺 0-600mm A3-1965
智能变频电源 AN97003H-3KVA 440203-0202
网络测试仪 Agilent FrameScope-Pro(N2620A) 400700-1901
400700-1902
4 系统技术指标
表3、外观质量
序号 检查项目 技术要求 检查结果
1 舱外设备漆膜颜色 RAL7001 □合格
2 舱外设备铭牌和标记 塑料标签/丝网印字 □合格
3 舱外设备外观检验 无划伤，无脱漆，外观完好 □合格
4 舱内设备漆膜颜色 中绿灰/设备本色 □合格
5 舱内设备铭牌和标记 钢质标牌/丝网印字 □合格
6 舱内设备外观检验 无划伤，无脱漆，外观完好 □合格

表4、设备尺寸
序号 名 称 型号 最大外形尺寸（mm）（宽×高×深） 数量 检查结果
1 网络机柜 600×950×800 1
2 AMP网络插座 30
3 AMP跳线 30
4 岸基接线盒 2

表5、安全性
序号 检查项目 技术要求 检查结果
1 绝缘电阻 ≥20 MΩ
2 机壳及金属可接触部位 不带电 □合格
3 接地电阻 ≤10 mΩ

表6、工作电源电压波动
序号 检查项目 技术要求 检查结果
1 电源适应性（AC198V~242V） 正常工作 □合格

表7、系统功耗
序号 检查项目 技术要求 检查结果
1 系统功耗 ≤1000W
表8、设备功能
序号 检验项目 技术要求 检查结果
1 局域网内部数据交互与通信 局域网内部的计算机可以进行数据的交互与通信
2 局域网接入互联网功能 局域网内部的计算机可以通过网络访问外部Internet

表9、技术参数测试
序号 检查项目 类型 技术要求 检查结果 备注
1 岸基接线盒 接口 网络/光纤 以外购件的合格证、使用说明书为依据
2 网络插座 接口 RJ45
3 千兆路由器 网络协议 PPPoE，DHCP，NAPT，NTP，DDNS 以外购件的合格证、使用说明书为依据
传输速率 10M/100M/1000Mbps
广域网接口 2个
局域网接口 3个
其他端口 1个Console接口
4 千兆交换机 应用层级 三层 以外购件的合格证、使用说明书为依据
传输速率 10M/100M/1000Mbps
交换方式 存储-转发
背板带宽 240Gbps
包转发率 72Mpps
MAC地址表 16K
端口数量 52个
端口描述 48个10/100/1000Base-T以太网端口
4个复用的1000Base-X千兆SF端口
控制端口 1个Console口

5
网络服务器 服务器类型 机架式 以外购件的合格证、使用说明书为依据
CPU类型 Intel Xeon E5606
CPU主频 2130MHz
CPU核心 四核心
标配CPU个数 1颗
二级缓存 8MB
内存类型 ECC DDR3
内存容量 4GB
硬盘类型 SATA,2T
光驱 可刻录DVD
扩展插槽 4个
网络控制器 集成的双千兆以太网卡
操作系统 Micrsoft Windows Server 2003、Red Hat EnterpriseLinux（可选装SUSE Linux Enterprise Server/Turbo Linux Enterprise Server/Novell Netware和VMware ESXI 3.5嵌入式虚拟机管理程序）
6 UPS电源 额定功率 3KVA 以外购件的合格证、使用说明书为依据
输出插座 国标2个
输入电压范围 115-300V
输入频率范围 40-60Hz
输出电压范围 220(1±2％)V
输出频率范围 50(1±0.2%)Hz

5 试验方法
5.1 外观质量
 测试标准：系统设备外表应无锈蚀、霉斑、涂复层剥落、划伤、毛刺、无机械损伤、开裂、起泡，并无明显变形等现象，文字标牌的标志清晰，控制元件及作用应安全正常。
 测试方法：采用目视、手感方法，对照外观要求进行检查。
5.2 设备尺寸
 测试标准：以表4所标注尺寸为测试标准。
 测试方法：采用游标卡尺对设备进行测量。
5.3 安全性
5.3.1 电气安装要求
 测试标准：
 产品通电后，机壳及金属可接触部位应不带电。
 系统与船金属体的连接，要求安全接地，其连接电阻应小于等于10mΩ。
 测试方法：
用手感法，毫欧表测量法和三用表测量法进行检验。
5.3.2 绝缘电阻
 测试标准：
 系统的电源插头与机壳金属外露部分间的常温绝缘电阻应大于等于20MΩ。
 测试方法：
用500V准确度为1.0级的兆欧表接至系统的电源插头（非接地端）与金属外露部分两端（电源开关置接通位置，但电源插头不接入电网内），在施加测试电压，待读数稳定后，读取绝缘电阻值应符合要求。
5.4 工作电源电压波动
 测试标准：
交流电源AC 198V～242V、50Hz。
 测试方法：
按系统接线图连接好，接通智能变频电源AC 220V，50Hz的交流电源，调节电压，使之显示交流电压为正常电压（AC220V），接通各设备电源，指示灯亮，接通网络服务器与显示器，观察局域网功能是否正常，如果不符合技术要求，应检查开关电源是否性能良好，更换器件应以排除。
5.5 系统功耗
 测试标准：
系统功耗≤1000W。
 测试方法：
直接读出智能变频电源上的系统功耗，应符合技术要求。
5.6 功能测试
根据系统连线图将各个部分按照要求相连起来，在确认无误后通电。
5.6.1 局域网内部数据交互与通信
 测试方法：
1） 按配套的系统接线图连接好设备，开启各设备的电源。
2） 在局域网内部的交换机上接上一台测试笔记本，在笔记本上通过软件与网络服务器进行数据的交互通信，发送文件给网络服务器；
 合格判据：
1） 笔记本能与网络服务器进行正常通信，并能正常发送文件到网络服务器上；
5.6.2 局域网接入互联网功能
 测试方法：
1） 按配套的系统接线图连接好设备，开启各设备的电源；
2） 在局域网内部的交换机上接上一台测试笔记本，在笔记本上通过网络访问外部Internet
 合格判据：
1） 笔记本能正常访问外部Internet；
5.7 参数测试
5.7.1 岸基接线盒
 测试标准：
检查项目 类型 技术要求 检查结果 备注
岸基接线盒 接口 网络/光纤 以外购件的合格证、使用说明书为依据

 测试方法及合格判据：
1） 查看岸基接线盒，接口满足技术要求为合格。
5.7.2 网络接座
 测试标准：
检查项目 类型 技术要求 检查结果 备注
网络插座 接口 RJ45 网络插座 接口

 测试方法及合格判据：
1） 查看网络插座，接口满足技术要求为合格。
5.7.3 千兆路由器
 测试标准：
检查项目 类型 技术要求 检查结果 备注
千兆路由器 网络协议 PPPoE，DHCP，NAPT，NTP，DDNS 以外购件的合格证、使用说明书为依据
传输速率 10M/100M/1000Mbps
广域网接口 2个
局域网接口 3个
其他端口 1个Console接口

 测试方法及合格判据：
1） “网络协议、传输速率”为检查该项技术指标由设备厂家技术保证和出厂检验，在此仅检查其设备的技术指标和出厂合格证。
2） 查看千兆路由器的端口，“广域网接口、局域网接口、其他端口” 满足技术要求为合格。
5.7.4 千兆交换机
 测试标准：
检查项目 类型 技术要求 检查结果 备注
千兆交换机 应用层级 三层 以外购件的合格证、使用说明书为依据
传输速率 10M/100M/1000Mbps
交换方式 存储-转发
背板带宽 240Gbps
包转发率 72Mpps
MAC地址表 16K
端口数量 52个
端口描述 48个10/100/1000Base-T以太网端口
4个复用的1000Base-X千兆SF端口
控制端口 1个Console口

 测试方法及合格判据：
1） “应用层级、传输速率、交换方式、背板带宽、包转发率、MAC地址表、端口描述”为检查该项技术指标由设备厂家技术保证和出厂检验，在此仅检查其设备的技术指标和出厂合格证。
2） 查看千兆交换机的端口，“端口数量、控制端口” 满足技术要求为合格。
5.7.5 网络服务器
 测试标准：
检查项目 类型 技术要求 检查结果 备注
网络服务器 服务器类型 机架式 以外购件的合格证、使用说明书为依据
CPU类型 Intel Xeon E5606
CPU主频 2130MHz
CPU核心 四核心
标配CPU个数 1颗
二级缓存 8MB
内存类型 ECC DDR3
内存容量 4GB
硬盘类型 SATA,2T
光驱 可刻录DVD
扩展插槽 4个
网络控制器 集成的双千兆以太网卡
操作系统 Micrsoft Windows Server 2003、Red Hat EnterpriseLinux（可选装SUSE Linux Enterprise Server/Turbo Linux Enterprise Server/Novell Netware和VMware ESXI 3.5嵌入式虚拟机管理程序）
 测试方法及合格判据：
1） “服务器类型、CPU类型、CPU主频、CPU核心、标配CPU个数、二级缓存、内存类型、内存容量、硬盘类型、光驱、扩展插槽、网络控制器”为检查该项技术指标由设备厂家技术保证和出厂检验，在此仅检查其设备的技术指标和出厂合格证。
2） 查看网络服务器，“操作系统” 满足技术要求为合格。
5.7.6 UPS电源
 测试标准：
检查项目 类型 技术要求 检查结果 备注
UPS电源 额定功率 3KVA 以外购件的合格证、使用说明书为依据
输出插座 国标2个
输入电压范围 115-300V
输入频率范围 40-60Hz
输出电压范围 220(1±2％)V
输出频率范围 50(1±0.2%)Hz
 测试方法及合格判据：
1） “额定功率、输出插座、输入电压范围、输入频率范围、输出电压范围、输出频率范围”为检查该项技术指标由设备厂家技术保证和出厂检验，在此仅检查其设备的技术指标和出厂合格证。









参试人员：













试验时间：

















附录1
系统示意图
A.1 系统示意图

結果 (英文) 1:

C13B CorvetteLocal area network systemFactory acceptance programA total of 10Guilin Lida Communications CorporationFebruary 2014C13B CorvetteLocal area network systemFactory acceptance programFiction: Audit: Sign: Sign: Sign: Approval: Document change logVersion number to modify content describing the modifier the date notesCatalogue1 objective 12 main components 13 Debugging Instrumentation 14 systems specification 15 test methods 45.1 quality 45.2 device dimensions 45.3 Security 45.3.1 electrical installation requirements 45.3.2 insulation resistance 45.4 power supply voltage fluctuation of 55.5 system power 55.6 functional test 55.6.1 LAN internal data exchange and communication 55.6.2 LAN to access the Internet features of 55.7 test 65.7.1 shore connection box 65.7.2 Access 65.7. the 3,000 m Router 65.7. a 4,000 switch 75.7.5 Network Server 75.7.6 UPS power supply 8Appendix 1-10A.1 system diagram 101 prefaceTest manual in accordance with the light frigate C13B of LAN equipment specification developed as the basis for equipment inspection.2 system componentsTable 1, test equipmentSerial number name and model number of the Unit notes1 network Cabinet 7 inch LCD monitor 1 2 opto-electrical Converter 1 single mode3,000 MB Router 1 4 Web server 1 5 1 48 Port Gigabit switch 6 AMP Super five 48 Port patch panel 1 7 3000VA UPS 1 8 folding type 1 mouse and keyboard set 9 AMP network socket 30 10 30 AMP jumper 11 base junction box 2 3 Debugging InstrumentationTable 2, debug using instrumentationName type equipment number effective dateDigital multimeter MY-65 260602-1902 Megger ZC25-3 260601-0804 Resistance tester for AT510PRO 360102-0801 Vernier caliper 0-600mm A3-1965 Intelligent variable frequency power supply AN97003H-3KVA 440203-0202 Agilent network tester FrameScope-Pro (N2620A) 400700-1901 The 400700-1902 4 systems specificationTable 3, appearance qualitySerial number check the technical requirements of the project results1 Eva equipment paint colour RAL7001-qualified2 outside equipment nameplates and tags/screen printing plastic labels-eligible3 external visual inspection of equipment and scratch-free, no paint, the appearance of well-qualified4 cabin equipment film color natural-grey/green devices in conformity5 cabin equipment nameplate and mark steel plate/screen printing-qualified6 the well equipment inspection and scratch-free, no paint, the appearance of well-qualifiedTable 4, equipment sizingSerial number name type maximum overall dimensions (mm) (w x h x d) quantity check results1 network Cabinet 600x950x800 1 2 AMP network socket 30 3 AMP jumper 30 4 shore junction box 2 In table 5, securitySerial number check the technical requirements of the project results1 insulation resistance ≥ 20 m ω 2 chassis and metal contacts electrically qualified3 grounding resistance ≤ 10 m ω Table 6, supply voltage fluctuationsSerial number check the technical requirements of the project results1 power supply adaptive (AC198V~242V) work properly-qualifiedTable 7, system power consumptionSerial number check the technical requirements of the project results1 power consumption ≤ 1000W Table 8, equipment featuresOrdinal survey project technical requirements of inspection resultsInternal data interaction and communication within the LAN 1 LAN computers are available for data interaction and communication 2 LAN to access the Internet features of computers within the LAN can access the external network Internet Table 9, measurement of technical parametersSerial number to check the project type technical requirement checks result notes1 base purchased outside the junction box/optical interface network based on certificate and user manual2 network jack connector RJ45 3,000 MB router network protocols other than PPPoE,DHCP,NAPT,NTP,DDNS to buy based on the certificate and user manualTransfer rate 10M/100M/1000Mbps WAN interface 2 LAN port 3 Other ports, 1 Console interface 4,000 switch is purchased outside the hierarchical three-layer based on the certificate and user manualTransfer rate 10M/100M/1000Mbps Exchange store-forward Backplane bandwidth 240Gbps Packet forwarding rate 72Mpps MAC address table 16K Port number 52 Port Description 48 10/100/1000Base-T Ethernet port1000Base-X Gigabit 4 reuse SF port Control ports, 1 Console port 5 Network Server server type rack purchase based on the certificate and user manualCPU type Intel Xeon E5606 CPU clock speed 2130MHz CPU core quad core Standard CPU number 1 The second level cache 8MB RAM type ECC DDR3 Memory 4GB The hard disk type SATA,2T Optical drive can burn DVD Expansion slot 4 Integrated Dual Gigabit Ethernet network controller card Micrsoft Windows Server 2003, the operating system Red Hat EnterpriseLinux (optional install SUSE Linux Enterprise Server/Turbo Linux Enterprise Server/Novell Netware and VMware ESXI 3.5 embedded hypervisor) 6 3KVA UPS power supply rated power purchases based on the certificate and user manualOutput socket GB 2 Input voltage range 115-300V Input frequency range 40-60Hz Output voltage range 220 (1 ± 2%) v Output frequency range of 50 (1 ± 0.2%) Hz 5 test methods5.1 appearance quality testing standard: System device appearance should be free of rust, mildew, cladding layer peeling off, scratches, burrs, mechanical damage, cracking, blistering, and no apparent deformation phenomena, text signs signs clear, control element and its role should be in safe condition. testing methods: using Visual methods, texture, checked against the appearance requirements.5.2 device dimensions testing standard: dimensioning table 4 for testing standards. testing methods: using Vernier calipers for measuring equipment.5.3 security5.3.1 electrical installation requirements measurement standards: product power, chassis and metal can contact position shall not be charged. system connected to the metal body of the ship, requiring safety grounding, connection resistance shall be less than or equal to 10m. testing methods:The handing method and milliohmmeter test measurement and three-meter measurement.5.3.2 insulation resistance measurement standards: the system's power plug and chassis ambient temperature insulation resistance between exposed metal parts should be greater than or equal to 20M. testing methods:Accuracy using 500V megohmmeter to system level 1 power supply plug (ungrounded side) and both ends of the exposed metal parts (power switch reset the position, but the power plug is not connected to the grid), applied test voltage readings become stable, read the insulation resistance value shall comply with the requirements.5.4 power supply voltage fluctuations measurement standards:AC power AC 198V~242V, 50Hz. testing methods:According to the wiring diagram of the system connected, connected inverter power supply AC 220V,50Hz AC power supply, voltage, which revealed a normal AC voltage is the voltage (AC220V), apply power to the device, led lights, connected to the network server and the monitor, observe the LAN function is normal, if you do not meet the technical requirements, you should check whether the switching power supply with good performance, replacement components should be excluded.5.5 system power consumption measurement standards:System power: 1000W Max. testing methods:Direct readout on the intelligent variable frequency power supply power consumption shall comply with the technical requirements.5.6 functional testingAll parts according to the wiring diagram of the system will be connected as required, after the confirmation power.5.6.1 LAN internal data exchange and communication testing methods:1) by supporting the system wiring diagram connect the device, open the device's power.2) inside the LAN switch connected to a test laptop, Notebook software communicates with the Web server for data communication, send a file to a network server; acceptable criterion:1) notebook can communicate properly with a Web server, and send the file to the network server properly;5.6.2 LAN access Internet functionality testing methods:1) by supporting the system wiring diagram connect the device, open the device's power;2) inside the LAN switch connected to a test laptop, notebook external network access on Internet acceptable criterion:1) notebook to access external Internet properly;5.7 test5.7.1 base junction box measurement standards:Project type technical requirements to check results of the inspection notesBase purchased outside the junction box/optical interface network based on certificate and user manual tests methods and acceptance criteria:1) see shore junction box interface meets the technical requirements for eligibility.5.7.2 network measurement standards:Project type technical requirements to check results of the inspection notesNetwork socket interface RJ45 network socket interface tests methods and acceptance criteria:1) view the network socket, interface meets the technical requirements for eligibility.5.7. the 3,000 m router measurement standards:Project type technical requirements to check results of the inspection notesGigabit router network protocols other than PPPoE,DHCP,NAPT,NTP,DDNS to buy based on the certificate and user manualTransfer rate 10M/100M/1000Mbps WAN interface 2 LAN port 3 Other ports, 1 Console interface  tests methods and acceptance criteria:1) "network protocol, transmission rate" for checking the specifications is guaranteed by equipment manufacturers and technical and factory inspection, just check the specifications of their equipment and factory certificate.2) viewing port Gigabit router, "WAN interface, LAN interfaces, other ports" meets the technical requirements for qualified.5.7. a 4,000 switch measurement standards:Project type technical requirements to check results of the inspection notesGigabit switch purchases outside the hierarchical three-layer based on the certificate and user manualTransfer rate 10M/100M/1000Mbps Exchange store-forward Backplane bandwidth 240Gbps Packet forwarding rate 72Mpps MAC address table 16K Port number 52 Port Description 48 10/100/1000Base-T Ethernet port1000Base-X Gigabit 4 reuse SF port Control ports, 1 Console port  tests methods and acceptance criteria:1) "application level, transmission rate, Exchange, backplane bandwidth, packet forwarding rate description, port, MAC address table" for checking the specifications is guaranteed by equipment manufacturers and technical and factory inspection, just check the specifications of their equipment and factory certificate.2) viewing port Gigabit switch, "port number, control port" meets the technical requirements for qualified.5.7.5 network servers measurement standards:Project type technical requirements to check results of the inspection notesNetwork Server server type rack purchase based on the certificate and user manualCPU type Intel Xeon E5606 CPU clock speed 2130MHz CPU core quad core Standard CPU number 1 The second level cache 8MB RAM type ECC DDR3 Memory 4GB The hard disk type SATA,2T Optical drive can burn DVD Expansion slot 4 Integrated Dual Gigabit Ethernet network controller card Micrsoft Windows Server 2003, the operating system Red Hat EnterpriseLinux (optional install SUSE Linux Enterprise Server/Turbo Linux Enterprise Server/Novell Netware and VMware ESXI 3.5 embedded hypervisor)  tests methods and acceptance criteria:1) "server type, CPU type, CPU clock speed, the number of CPU cores, standard CPU, cache, memory type, memory size, the type of hard drive, optical drive, expansion slot, a network controller" to check the technical specifications is guaranteed by equipment manufacturers and technical and factory inspection, just check the specifications of their equipment and factory certificate.2) see network server "operating system" meets the technical requirements for qualified.5.7.6 UPS power supply measurement standards:Project type technical requirements to check results of the inspection notes3KVA UPS power supply rated power purchases based on the certificate and user manualOutput socket GB 2 Input voltage range 115-300V Input frequency range 40-60Hz Output voltage range 220 (1 ± 2%) v Output frequency range of 50 (1 ± 0.2%) Hz  tests methods and acceptance criteria:1) "rated power output socket, input voltage range, output voltage, output, input frequency range frequency range" to check the technical specifications is guaranteed by equipment manufacturers and technical and factory inspection, just check the specifications of their equipment and factory certificate.Participants:Test time:Appendix 1System diagramA.1 system diagram

結果 (英文) 3:

C13B light frigate
LAN system


factory acceptance outline






a total of 10





Guilin Lida Communication Engineering Co. Ltd in February

2014







C13B light frigate
LAN system


factory acceptance outline













Fiction:
audit:
will sign:
will sign:
will sign:
approval:


document revision recording
version number modify modify the contents of the main equipment People




date note



















the directory
1 introduction 1
2 system composed of 1
3 debugging with the technical index of the instrument instrument 1
4 system 1
description4
5.1 5 test method for appearance quality of 4
5.2 device dimensions 4
5.3 security 4
5.3.1 electrical installation requirements of 4
5.3.2 insulated power 5
5.6 function resistance 4
5.4 working voltage fluctuation of the power supply 5
5.5 system internal data to test the 5
5.6.1 local area network interaction and communication of 5
5.6.2 LAN Internet access function of 5
5.7 parameter test of 6
5.7.1 base 6
5.7.2 junction box network connecting seat 6
5.7.3 Gigabit router 6
5.7.4 Gigabit switch 7
5.7.5 server 7
5.7.6 UPS power supply 8
Appendix 1 of 10
A.1 system schematic diagram of 10


1 objective
The test manual and formulated according to the "C13B light frigate LAN system equipment technical specification", as the basis of inspection equipment. Table 1 Composition of
, EUT component
ordinal name and type number quantity unit note
1 network cabinet 7 inch liquid crystal display 1
2 photoelectric converter 1 single mode
3 Gigabit router network
4 1 server 1
5 48 port Gigabit switch 1
6 AMP super five 48 mouth distribution frame 1
7 3000VA UPS 1
8 foldable mouse and keyboard 1 sets of
9 AMP network socket 30
10 AMP jumper 30

2 main equipment system11 shore connection box 2

3 debug instrumentation
Table 2, debugging using instrumentation
name type instrument No. expiry date
digital multimeter MY-65
260602-1902 megohmmeter of ZC25 3 260601-0804
resistance tester AT510PRO 360102-0801
A3-1965
vernier caliper 0-600MM intelligent variable frequency power supply AN97003H-3KVA 440203-0202
Agilent network tester FrameScope-Pro (N2620A) 400700-1901
400700-1902
4 system technical indicators in Table 3, the appearance of quality

serial number check the technical requirements of the project examination results
1 outside the cabin equipment paint color RAL7001 acceptable
2 outside the cabin equipment nameplate and marking of plastic label / silk screen printing acceptable
3 outside the cabin equipment appearance inspection no scratch, no paint, exterior condition acceptable Zhonglu
4 equipments in the cabin paint color grey / device color acceptable
5 cabin equipment nameplate and mark steel plate / screen printing acceptable equipment
6 cabin appearance inspection no scratch, no paint, exterior condition acceptable

Table 4, the size of the equipment
serial number name type maximum size (mm) (w * h * d) number and the results of
1 network cabinet 600 x 950 x 8001
2 AMP network socket 30
3 AMP 30
4 base jumper junction box 2

table 5, safety
serial number check the technical requirements of the project and the results of
1 insulation resistance is greater than or equal to 20 M Omega
2 casing and metal can contact position is not charged acceptable
3 grounding resistance is less than or equal to 10 m Omega

table 6, operating power supply voltage fluctuation
number check project technical requirements the results of
1 power adaptation (AC198V~242V) work normally acceptable


table 7, the power consumption of the system serial number check the technical requirements of the project and the results of
1 system power consumption is less than or equal to 1000W
Table 8, equipment function
number test the technical requirements of the project examination results
1 internal data local area network interaction and communication within the LAN computer can conduct internal interaction and communication of
2 LAN Internet access function of LAN of computer data through the network to access the external Internet

Table 9, technology parameter test
serial number check project type technical requirements of inspection results note
1 base junction box interface network / fiber other than the purchase of qualified certificate, parts of the instructions for use as the basis of
2 network socket interface RJ45
3 Gigabit router network protocol of PPPoE, DHCP, NAPT, NTP, DDNS other than the purchase of qualified certificate, parts of the instructions for use as the basis of
Transmission rate of 10M/100M/1000Mbps
WAN interface 2
3
other LAN interface port 1 Console interface
4 Gigabit switch application level three layer other than the purchase of qualified certificate, parts of the instructions for use as the basis of
10M/100M/1000Mbps
exchange transmission rate store forwarding backplane bandwidth 240Gbps

packet forwarding rate of 72Mpps
16K
MAC address table port number 52
port description 48 10/100/1000Base-T Ethernet port
4 multiplexed 1000Base-X Gigabit SF ports
control port 1 Port Console

5
Outside the network server server type rack share certificate, parts of the instructions for use as the basis of type Intel Xeon E5606
CPU
CPU frequency 2130MHz
CPU
four core core standard CPU number 1 A
two level cache memory type 8MB
ECC
DDR3
4GB memory hard disk type SATA, 2T
CD-ROM recordable DVD
4
network expansion slot controller integrated dual Gigabit Ethernet
operating system Micrsoft Windows Server 2003,Red Hat EnterpriseLinux (SUSE Linux Enterprise Server/Turbo can be installed Linux Enterprise Server/Novell Netware and VMware ESXI 3.5 embedded hypervisor) outside the
6 UPS power supply rated power 3KVA share certificate, parts of the instructions for use as the basis of output socket GB
2
input voltage range input frequency range 115-300V
40-60Hz
220 (output voltage range 1 + 2%)
V output frequency range of 50 (1 + 0.2%)
5.1 test method

5 Hz appearance quality
is testing standards: system equipment appearance should be no rust, mildew,Coating spalling, scratch, burr, no mechanical damage, cracking, blistering, no obvious deformation phenomena, mark clear text label, control components and effect should be safe and normal. Test method: using
is visual, touch method, control the appearance check.
5.2 device dimensions
is testing standards: in Table 4 for the test standard dimension.
is test method: using vernier caliper measurement of the equipment.
5.3 security
5.3.1 electrical installation requirements:
-
is testing standard products after electrifying, casing and metal contact parts should not be charged.
connection - system and ship metal body, the safety requirements for grounding,The connection resistance should be less than or equal to 10m. Test method:

is feeling method, milliohm meter measurement and three table measurement test.
5.3.2 insulation resistance test standard:

is insulated power plug and the casing metal exposed part - system between normal temperature resistance should be greater than or equal to 20M. Test method:

is used as the power plug 500V accuracy level 1 megohm meter is connected to the system (non grounding end) and the metal exposed part ends (power switch arranged on position, but the power plug is not connected to the electricity grid in), in the test voltage is applied, to be a stable reading, read the value of insulation resistance should meet the requirements.
5.4 operating power supply voltage fluctuation is testing standards:

AC AC power supply of 198V ~ 242V, 50Hz. Test method:

is connected according to system wiring diagram, connect the intelligent variable frequency power supply AC 220V, AC power supply, the 50Hz voltage regulation, which can display normal voltage AC voltage (AC220V), power on the device, the indicating lamp is bright, connect to the network server and the display, observe the LAN function is normal, if not comply with technical requirements, should check whether the good performance of switching power supply, the replacement of the device should be to exclude.
5.5 system power dissipation is testing standards:

the system power consumption is less than or equal to 1000W. Test method:

isDirect readout system power consumption intelligent frequency conversion power supply, shall meet the technical requirements.
5.6 function test
each component will be in accordance with the requirements of connected according to the system connection diagram, electricity in confirmation. Test method of
5.6.1 internal LAN data interaction and communication
is:
1) connect the devices according to the system wiring diagram matching, power on each device.
2) in the internal LAN switches connected to a test notebook, interactive communication data through software and network server in a notebook, sending files to the network server;
is criterion:
1) notebook can be a normal communication and network server,