1.不论机型，存放机器的室内温度绝对不能低于0℃，如果条件具备，请把温

1.不论机型，存放机器的室内温度绝对不能低于0℃，如果条件具备，请把温度保持在14摄氏度以上。
2.如果假期期间公司有人值班，请每天打印喷头测试条检查喷头是否有堵塞，如有堵塞请执行清洗操作，以确保喷头保持良好状态。最好做一个各色色值各是50－90左右的复合黑色块，每天打印一次，至少60cm宽20cm长。
3.如果公司无人值班。离开之前：
（1）打印测试条，保证喷头状态正常，没有断墨。
（2）使用溶剂、弱溶剂墨水的机器用干净棉签，专用的清洗液；使用水性墨水的机器用干净棉签、纯净水（！注意：最好是纯净水，绝对不能用自来水）将喷头擦拭干净。（！注意：最好单向擦拭，不要画圈式的涂抹）
（3）有休眠设置的机器，开启机器休眠后自动清洗和闪喷的功能，不要关闭机器主电源，只要关闭操作电源即可。开启休眠设置之后，机器将会根据你设置的间隔时间自动执行喷头清洗或闪喷。
（4）有泡喷头功能的机型：进行泡机操作，可以把泡机时间设置的稍微长一些（！注意：不要关闭主电源）；没有泡喷头功能的机型：使用溶剂、弱溶剂墨水的机器在墨栈中滴入专用清洗液，使用水性墨水的机器在墨栈中滴入纯净水,用绳子或者橡皮筋扎住墨栈的下墨管，然后关闭主电源。
（5）可以设置写真机喷头高低档的机型，尽量将机器喷头设置于低位，以使喷头与墨栈尽可能的闭合。 （6）室内温度接近0℃或者停机时间超过10天或者墨管有漏气、墨栈与喷头不能正常闭合的机器，建议拔出墨盒封存好，将墨管内墨水退墨清洗管道，将喷头拆下清理干净，喷头涂上专用喷头保护液，用保鲜膜包裹好。
有些人认为写真机喷头堵塞无关紧要，在此提醒诸位，写真机喷头堵塞轻则需要反复清洗喷头，并出现斜喷、偏针、飞墨等状况，喷头使用寿命变短，重则严重堵塞、窜墨、侧漏、隔膜破裂造成喷头直接报废。所以大家一定要在假期里注意写真机的保养维护。

結果 (英文) 1:

1. models, store the machine indoor temperature must not be less than 0 ℃, if conditions are met, please keep the temperature above 14 degrees Celsius. 2. If someone on duty during the holidays, please check nozzle print head test strip a day whether there is a blockage, such as jam perform the cleaning operations, to ensure that the sprayer in good condition. Best to do a colored compound black color value is about 50-90, once a day, at least 60cm wide and 20cm long. 3. If the company unattended. Before you leave:(1) printing tests, ensure the nozzle in normal state, did not break the ink. (2) the use of solvent, eco solvent ink machine with a clean cotton swab, special cleaning fluid; using water based ink machine with a clean cotton swab, pure water (! Note: it is pure water, never use tap water) spray nozzle clean. （！ Note: best single wipe, don't circle-style painting)(3) machine with hibernation settings, opening machine automatic washing and splash spray after hibernation feature, do not turn off the main power supply of the machine, as long as the closing power. Open the hibernate after setting, the machine will be based on the time interval you set automatic nozzle cleaning spray or Flash.(4) foam sprayer function models: for machine operation, machine time settings can be a little longer (! Note: do not turn off the main power) without foaming nozzle features models: use solvent, eco solvent ink machine ink drop into the cleaning liquid in the stack, using water based ink machine ink drops into the pure water in the stack with string or a rubber band ligation ink ink tube under the stack, and then turn off the main power.(5) photo machine nozzle can be set high-low-models, the nozzle of the machine is set at a low level as much as possible, so that the nozzle and ink stack closed as much as possible. (6) the indoor temperatures close to 0 degrees or down time more than 10 days or ink pipes leak, stack machine with the nozzle does not close properly, it is recommended that pull out the cartridge sealed, will return the ink inside ink ink clean pipe, remove the nozzle cleaning, spray painted with special sprinkler protection, wrap with plastic wrap.Some people think the photo machine nozzle blocked doesn't matter, remind you that photo machine nozzle blockage of light you will need to repeat the cleaning nozzle, spray and oblique, needles, ink flying conditions, nozzle service life is shorter, while blocked, channeling ink, caused by leakage, rupture of diaphragm nozzle directly discard. So make sure to note that during the holidays the machine maintenance.

結果 (英文) 3:

芯片组