玉米剥皮机使用及安全防护 1、固定好电动机，使两槽轮在同一条线上，接好

玉米剥皮机使用及安全防护 1、固定好电动机，使两槽轮在同一条线上，接好电源，必须接好地线，好反正转后，空转5分钟后停机检查各部位螺丝是否松动，三角带的松紧情况，润滑部位是否发烫，以及两新的压紧情况，如有异常要进行调整。 2、粗胶辊与细胶辊是无间隙配合，粗胶辊靠调整弹簧的压力，通过摇臂的作用将其紧紧压在细辊上，弹簧节距越大，其压力越小，传给粗胶辊压力就小，反之越大，弹簧节距调整要求在2-4mm左右，这是影响剥皮效果的关键所在，本机出厂时已调整到使用位置范围内，但根据实际情况用户应随时注意调整。 3、玉米剥皮机作业前就盖好各传动部位的防护罩，作业中必须执行安全第一的规定，严格按操作规程办事，不得有任何疏忽，特别注意事项如下:⑴果穗必须平行均匀喂入,不得上下重叠喂入,在工作过程中发现有竖立起来的果穗时,应加大喂入量,用新喂入的果穗将其挤倒。⑵机下苞叶和机后果穗，必须及时清理出机外，否则易造成苞叶缠新或堵塞出口。⑶工作人员不得将手伸入喂入口挡板，以防意外。⑷卡辊或绕辊后必须停机处理，不得在转动时处理。⑸严禁砖，石，木块等硬物喂入。

結果 (英文) 1:

Corn peeling machine use and safety protection a fixed good motor, so that the two sheaves on the same line, connect the power, it must take a good ground, well anyway, turn after 5 minutes idling stop to check that all the screws are loose, V-belt tightness, lubrication parts are hot, as well as two new compression and, if an exception should be adjusted. 2, coarse and fine rubber roller rubber roller is no gap with the thick rubber roller by adjusting the pressure of the spring, through the role of the rocker arm tightly pressed its fine roller, spring pitch, the greater the pressure on the smaller mass give crude rubber roller pressure is small, whereas the larger spring pitch adjustment requires about 2-4mm,This is the key to affecting peeling effect, the factory has been adjusted to a use position range, but according to the actual situation of the user should always pay attention to adjust. 3, corn peeling machine before operating the transmission cover parts of the shield, the job must perform safety first, and shall strictly follow the rules and act, without any negligence, special precautions are as follows: ⑴ ear must be parallel uniform feeding not overlap the upper and lower feed, found in the work process erected ear, should increase the feed rate, feed the ear with a new squeeze down their. ⑵ machine and dryer consequences under the bract spike must be promptly cleaned out the machine,Otherwise easily lead to new or blockage husk wrapped export. ⑶ staff shall not reach into the feed inlet baffle to prevent accidents. ⑷ card roll or post-roll around the handle must be shut down, not in the rotation process. ⑸ prohibited brick, stone, wood and other hard objects feeding.

結果 (英文) 2:

Corn peeling machine use and security 1, fixed the motor, so that the two groove wheels in the same line, connect the power, must be properly earthed, well anyway after the turn, idle stop screw after 5 minutes to check whether all parts of loose, loose V-belts, lubricating parts is hot, and press two new, such as abnormal to adjust. 2, the coarse and fine rubber roller roller is gapless combined with coarse rubber roller, by adjusting the spring pressure, through a rocker arm role be tightly pressed on the fine roller, spring pitch is bigger, the pressure is small, to the crude rubber roller pressure is small, but larger, spring pitch adjustment requirements at about 2-4mm,This is the key of peeling effect, this machine factory has been adjusted to a use position range, but according to the actual situation of the user should always pay attention to adjust. 3, corn husker working before the transmission parts cover the protection cover, provisions must be safety first operation, strict operation rules, there may not be any negligence, special attention is as follows: the ear must be parallel uniform feeding, not on the overlap feeding, found the ear has erected in in working process, should increase the feeding quantity, use ear new feeding pushing down. The machine bracteal leaf and ear, must be promptly cleaned out of the machine,Otherwise, easy to cause the bract Chanxin or blocking the outlet. The staff may not be the hand into the feed entrance baffle, to prevent accidental. The card roller or roller winding must stop processing, not in rotation. It is strictly prohibited to brick, stone, wood and other hard material feeding.

結果 (英文) 3:

Corn skinning machine using and the security protection 1, and fixed good motor, make two slot round in same article line Shang, pick good power, must pick good ground, good anyway go Hou, idling 5 minutes Hou downtime check the parts screws whether loose, triangle with of elastic situation, lubrication parts whether made hot, and two new of pressure tight situation, as has exception to for adjustment. 2, fine rough rollers and rollers are no clearance fit, thick rubber roller pressure adjusting spring, tightly pressed it over the rocker on the fine roll, larger pitch of spring, the pressure the less, to rough roller pressure on the small, rather larger spring pitch claims at around 2-4mm,The key to this is affecting the skin effect, native range is factory-adjusted to using location, according to the actual situation, however users should note adjustments at any time. 3, and corn skinning machine job Qian on cover good the transmission parts of protection cover, job in the must implementation security first of provides, strictly by practice for do, shall not has any negligence, special attention matters following: ⑴ ear must parallel uniform feed into, shall not upper and lower overlap feed into, in work process in the found has erected up of ear Shi, should increased feed into volume, with new feed into of ear will its squeeze pour. ⑵ husks and the consequences under Spike, must promptly clean up the machines, theOtherwise cause husks wrapped around new or blocking exports. ⑶ staff may not reach into the feed inlet baffle to prevent accidents. ⑷ card around a roller or roller must stop after processing, shall, in turn, to address. V non-brick, stone, wood and other hard object feeding.