Take caution when inserting the pro

Take caution when inserting the product into the cabinet or opening the door because your fingers may be caught.
Do not let the product stand on the power cable when installing into the cabinet.
- Damaged cables may cause fire or electric shock.
After placing the product, plug the power cable into the wall socket.
The guides included in the Install Kit are used for fitting the cabinet.
Do not use for other purposes.
If do not install as provided method, the Energy will be increased.
Turn clockwise to loosen the leg by 9.0 mm(8 turns).
Put the provided Foam PE on 4 places at the rear of the product.
Align the left edge of the product with the left wall of the cabinet, and turn the right edge of the product to the right wall of the cabinet as shown.
Insert the product into the cabinet so that the bottom of the product is in line with the bottom of the cabinet.
Adjust the leveling legs to keep the product and cabinet in line.
If the upper area of the product protrudes:
Turn the legs clockwise to level.
If the upper area of the product collapses:
Turn the legs counter clockwise to level.
Insert the provided ‘ㄱ’-shaped accessory on either side of the refrigerator between the cabinet and the refrigerator as shown to fill the gap.
You can use the provided “SHEET B” to fill the gap against either side wall.
Put the guides in the rear corners of the cabinet.
Use the level to check if the floor where the provided
guides are installed is level.

結果 (繁體中文) 1:

在向內閣或打開了大門，因為可能會抓住你的手指插入產品時採取謹慎態度。不要站在電力電纜入機櫃安裝時的產品。-損壞的電纜可能引起火災或電擊。後放置產品，將電源線插到牆上的插座。導軌安裝工具組中包含用於擬合內閣。不用於其他目的。如果不安裝作為提供的方法，將增加能量。順時針由 9.0 毫米 （8 圈） 放鬆腿部。提供的發泡聚乙烯放 4 地方背面的產品。該產品與左牆的櫃子，左側的邊緣對齊和轉到右邊的牆的內閣所示產品的右邊緣。產品插入內閣，以便底部的產品是符合機櫃底部。調整找平的腿保持一致的產品和內閣。如果該產品的上部區域突出 ︰水準的順時針旋轉的雙腿。如果該產品的上部區域折疊 ︰輪到腿逆時針到的水準。插入提供 'ㄱ'-形兩邊的內閣與冰箱冰箱配件，填補了國內空白，如上所示。您可以使用提供的"工作表 B"填補了國內空白或側牆上。放在內閣後方角落的指南。使用水準檢查如果地板在哪裡提供安裝指南是水準。

結果 (繁體中文) 3:

請小心，將產品插入櫥櫃或打開門，因為你的手指可能會被抓住。不要讓產品在電源線安裝到機櫃時。•損壞的電纜可能會引起火灾或電擊。將該產品放置後，將電源線插頭插入插座。安裝包中包含的指南用於安裝機櫃。不用於其他用途。如果不安裝的方法，能量會新增。順時針旋轉，以放鬆腿部9毫米（8轉）。將所提供的泡沫資料放在產品尾部的4個地方。將該產品的左邊緣與機櫃的左牆對齊，並將產品的右側的右牆打開，如圖所示。將產品插入機櫃，使產品底部與機櫃底部一致。調整平腿以保持產品和機櫃的生產線。如果產品的上部區域突出：順時針旋轉腿。如果產品的上游地區崩潰：把腿逆時針旋轉到水准。將提供的“ㄱ”形附件兩邊的冰柜之間的櫥櫃和冰柜如行雲流水。你可以用“紙”來填充牆的縫隙。放在櫃後角的導軌。使用該級別檢查所提供的樓層安裝指南是一級。