熔铝炉是根据铝熔炼工艺而开发的一种新型高效节能炉，它能很好地满足铝熔炼

熔铝炉是根据铝熔炼工艺而开发的一种新型高效节能炉，它能很好地满足铝熔炼工艺中：合金成份要求严，生产不连续，单炉容量较大等要求，达到了降低消耗，减小烧损，提高产品质量，降低劳动强度，改善劳动条件和提高生产效率之功效，适用于间歇作业，配合金及回炉料多的熔炼。
结构形式及特征：
1、采用圆形底炉及合理的燃烧器配置，炉气循环强烈，炉温均匀，无局部过热过烧现象，提高产品质量，延长炉子使用寿命。
2、采用竖炉：炉料在竖炉中充分吸收烟气余热，降低炉顶排烟温度，大大提高热效率，而炉料进入底炉时已预热到接近熔化状态，保证了很高的熔化速率和很低的能耗。
3、采用空气预热器及炉壳夹层风道：空气预热器很好地吸收烟气余热，预热后的空气进入炉壳夹层风道，进一步预热升温，相对提高环境温度，减少炉壳散热，空气预热后能提高燃烧效率，燃烧强度，火焰温度与速度，强化炉气循环和升温速度。
4、炉门结构合理密封，炉门口无须加炉；炉门密封严，开启时间少，炉内散热损失小，无扒渣精炼死角，操作方便，操作环境好。
5、炉顶加料：加料方便，劳动强度低，炉温波动小，炉龄长，加料不占用熔化时间。
6、采用高效节能燃烧器为热源，具有点火易，升温快，喷速高，燃烧安全，空气过剩系数小等特点。
技术参数
1.能耗≤65万大卡/吨铝。
2.炉体规格有:1.5T,2T,3T,4T,5T,6T,8T,10T,12T,15T,18T,20T,25T.可根据用户要求进行特殊设计。
3.铝损指标≤1.2%。
说明:主要经济技术指标：指每炉达到额定容量，回炉料不超过30%（洁净料）,其余为铝锭，在炉子时进入热平衡状态并正常生产的条件下，从加料到铝液达到740℃过程中所达到的指标。

結果 (英文) 1:

Aluminum melting furnace is based on the aluminum smelting process and the development of a new energy-efficient furnace, which can well meet the aluminum smelting process: alloy composition strict requirements, the production is not continuous, single furnace larger capacity and other requirements, to reduce consumption , reducing the burning, improve product quality, reduce labor intensity and improve working conditions and productivity of the effect, suitable for intermittent operation, with gold and multi-smelting furnace returning.
Structure and characteristics:
1, using a circular hearth furnace burner configurations and reasonable, strong air circulation furnace, furnace temperature uniformity, no local overheating over-burning phenomenon, improve product quality, extend the service life of the furnace.
2, the use of furnace:Charge fully absorbed in the shaft furnace flue gas waste heat, reduce roof exhaust gas temperature, which greatly improve the thermal efficiency, and charge into the bottom of the stove has been preheated to near molten state, to ensure a high melting rate and very low energy consumption.
3, the use of the air preheater and furnace shell laminated duct: air preheater flue gas heat well absorbed, preheated air into the furnace shell sandwich air duct, further preheat temperature, the relative increase ambient temperature, reducing furnace shell cooling, air preheating combustion efficiency can be improved after the combustion intensity, the flame temperature and speed, air circulation and strengthen the furnace heating rate.
4, the door sealing structure is reasonable, no need to increase the furnace door furnace;Door seal strict, less time on the furnace heat loss is small, no slag refining corners, easy operation, good operating environment.
5, top charging: charging convenient, low labor intensity, temperature fluctuation is small, long furnace, feeding do not take up the melting time.
6, the use of energy-efficient burner as the heat source, with the ignition and easy, fast heating, high-speed jet, combustion safety, the excess air coefficient and so on. Technical parameters

1. Consumption ≤ 65 million kcal / ton of aluminum.
2. Furnace specifications: 1.5t, 2t, 3t, 4t, 5t, 6t, 8t, 10t, 12t, 15t, 18t, 20t, 25t. According to user requirements for special designs.
3 aluminum loss index ≤ 1.2%.
Description:Main economic indicators: refers to the rated capacity of each furnace, back to the charge of not more than 30% (clean material), the rest of ingots in the furnace into thermal equilibrium state and normal production conditions, fed from the liquid aluminum reaches 740 ℃ process achieved in the target.

結果 (英文) 2:

Aluminum melting furnace is a new type of high efficiency energy saving furnace according to the aluminum smelting process and development, it can well meet the aluminum smelting process in the alloy composition: strict requirements, production is not continuous, single furnace capacity requirements, to reduce consumption, reduce loss, improve product quality, reduce labor intensity, improve working conditions and improve the efficiency of the production function, is suitable for intermittent operation, alloying and returns multiple melting.
structure and characteristics:
1, using a circular hearth furnace and burner configuration, the circulation of the furnace gas strong, uniform furnace temperature, no local overheating overheating, improve product quality, prolong the service life of furnace.
2, the shaft furnace:Charge in the shaft furnace in fully absorb the flue gas waste heat, reducing roof exhaust temperature, thermal efficiency is greatly improved, and the charging into the bottom oven preheated to near the melting state, the melting rate is very high and very low energy consumption.
3, the air preheater and the furnace shell laminated air: air preheater well absorb the waste heat of flue gas, preheated air into the furnace shell laminated duct, further preheating, the relative improvement of environmental temperature, reduce the furnace shell cooling, air preheating can improve combustion efficiency, combustion intensity, flame temperature and velocity, strengthen the furnace gas circulation and heating rate.
4, door structure reasonable furnace door sealing, without adding furnace;The door sealing, opening time less, small heat loss of the furnace refining slag, no dead angle, convenient operation, good operating environment.
5, top charge: convenient charging, low labor intensity, the temperature fluctuation is small, long life, feeding off the melting time.
6, the use of highly efficient energy-saving burner to heat, with easy ignition, quick temperature rising, high spraying speed, the combustion characteristics of safety, excess air coefficient is small.
technical parameters of
1. ≤ 650000 kcal / ton of aluminum consumption.
2. furnace body specifications are: 1.5T, 2T, 3T, 4T, 5T, 6T, 8T, 10T, 12T, 15T, 18T, 20T, 25T. according to user requirements for special design.
3. aluminum loss index ≤ 1.2%. Explain.The main economic and technical indicators: refers to the furnace to achieve the rated capacity, returns no more than 30% (Jie Jingliao), the rest is aluminum, into the thermal equilibrium state in the stove and the normal production conditions, from the feed to liquid aluminum reaches to 740 ℃ process index.

結果 (英文) 3:

Melt aluminum furnace is according to aluminum melting technology and development of a new efficient energy furnace, it can is good to meet aluminum melting technology in the: alloy ingredients requires yen, production not continuous, single furnace capacity larger, requires, reached has reduced consumption, reduces burn loss, improve products quality, reduced intensity, improved working conditions and improve production efficiency of efficacy, applies Yu intermittent job, tie gold and the melted down material more of melting.
Structure and characteristics:
1, uses the end of circular burner of the stove and a reasonable configuration, furnace gas cycling strongly, even furnace temperature, without local overheating over burning, improving product quality, extending the life stove. Shaft furnace in
2, use:Charging fully absorbed in a shaft furnace gas waste heat, lower the roof flue gas temperature, greatly improving the thermal efficiency and charging into the furnace preheated to close by the end of melted State, guarantees a very high melting rate and very low energy consumption.
3, using mezzanine air duct air heaters and furnace shells: waste heat from flue gas of air heater is well absorbed, preheated air into the furnace shell after the mezzanine air duct, Preheat warming further, relatively higher ambient temperatures, reduces heat after preheating the air increases combustion efficiency, burning intensity, flame temperature and speed, strengthen the gas circulating and heating rate.
4, oven and well-structured sealed furnace door and need to increase furnace;Oven door seals, opened with little time in furnace heat loss, no slag refining dead, easy, good operating environment.
5 and the top charged: charging, low labor intensity, less temperature fluctuation, furnace longer feeding without melting.
6, using energy-efficient burner for heat, ignition, heating up fast, high injection speed, combustion safety, air excess coefficient, and other characteristics. Technical parameters of

. energy consumption ≤ 650,000 kcal/ton of aluminum.
2. furnace specifications: 1.5T,2T,3T,4T,5T,6T,8T,10T,12T,15T,18T,20T,25T. can be designed according to the user's specific requirements.
3. aluminum loss indicator is less than 1.2%.
Note:Main economic indicators: reach rated capacity of each furnace, recycled materials does not exceed 30% (clean feed), and the rest for aluminum ingot, at the stove enters the thermal equilibrium State and under normal conditions of production, from expecting aluminum melt up to 740 ° c indicator reached in the process.