现在的1500W电机大多是45的磁钢，很多电机其实都可以用48V超压到

现在的1500W电机大多是45的磁钢，很多电机其实都可以用48V超压到96V或者更高。（特别是1500W10寸）
这个证明了什么呢？
电压升高后磁性依然可以上去。
电机想要磁性增强有
1 电压不变增加线圈匝数。（可惜我们的电机都是绕满了，绕不下了）电流不变。（加大电流，很快就会烧坏电机）
2 电压不变减少线圈匝数增加并联漆包线条数，加大电流。（只要电流饱和，速度肯定快过原来的电机。因为瓦数增加了。）
3 电压升高，其他方面不变，一直超压到5000W，这样基本不用改变多少东西就能得到更快得速度，（当然使用功率降低了，因为铁心的体积问题，磁铁的强度问题存在。）可是现在的电机又有谁愿意小批量生产高效率的电机呢？所以超压到5000W是最直接的方法了。

下面我给大家介绍一下一个最好的方案
材质：
首先看看你的电机是用上面颜色的铜线绕的，如果是黄色的，那应该是一般的低温铜线，建议你可以用耐高温的铜线，其颜色是深棕色的。
如果你的是耐高温铜线，还想更好，那么就是镀银线了。最好的是纯银导线。（可以很明确的告诉你，哪怕你用纯银导线，也跟你买一个5000W电机差不多的价格。）
绕法，
首先你要看你想要多快，48V1500W是6并7个每圈，绕一个后就要跳跃2个再绕7圈，3000W是可以在1500W的接线对面剪掉3个不同相得线圈连接处来重新连接的，顺时针方向的3条接起来，另外的3条找出跟原来的ABC线连接起来。这就是3000W这个方法简单，实用，手工好的，不亚于大厂的产品，记得剪短电机线，电机线太长电阻会非常大，发热量也更大，所以改装后要不就是改掉电机线，要不就是尽可能的短。
4500W就是找到3分之一的点，同上方法，
6000W就是找到4分之一的位置，同上
超过6000W无法改了。因为实用功率太低了
不建议用了

結果 (中文) 3:

Now most of the 45 1500W motor magnet, many motor actually can be used 48V overpressure to 96V or higher. (in particular, 1500W10 inch)What does this prove?After the voltage is increased, the magnetism can still go up.The motor wants to enhance the magnetic properties1 voltage constant increase coil turn number. (it's a pity that our motors are all around, and can't be turned off). (increase the current, will soon burn out the motor)2 voltage unchanged reduce the number of parallel wire winding turns to increase the number of parallel wire, and increase the current. (as long as the current is saturated, the speed must be faster than the original motor. Because the tile has increased.The 3 voltage increases, other aspects of change, has been pressure to 5000W, which basically does not change the number of things can get faster speed, (of course, using power is reduced, because the volume of core strength, the presence of a magnet.) But now the motor and who are willing to small batch production of high efficiency motor? So super pressure to 5000W is the most direct method.Let me give you a brief introduction to the best programTexture of material：First look at your motor is used in the above color of copper wire, if it is yellow, it should be the general low temperature copper wire, it is recommended that you can use the high temperature resistant copper wire, its color is dark brown.If you are resistant to high temperature copper wire, but also want to be better, then it is the silver plated wire. The best is the silver wire. (can tell you very clearly, even if you use silver wire, to buy you a 5000W motor similar price.)Winding method,Do you want to see how quickly you want to first of all, 48V1500W is 6 and 7 each around a circle, will jump 2 to 7 times around, 3000W can be cut in the wiring 1500W across 3 different phase coils connected to reconnect, clockwise 3 pick up, in addition 3 to find the original ABC line connected. This is 3000W this method is simple, practical, good hand, as manufacturers of the products, remember to cut the motor line, the motor line is too long the resistance will be very large, the heat is greater, so the modified or get rid of the motor line, or as short as possible.4500W is to find a point of 3 points, the same as the method,6000W is to find the location of 4 points, the same as above.More than 6000W can not be changed. Because the utility power is too low.It is not recommended to use