In this tutorial it is explained ho

In this tutorial it is explained how to add and configure 6 x wired zones:
1. Security Module Zone 1 - Door Sensor configured as Normally Closed Zone
2. Security Module Zone 2 - Window Sensor configured as Normally Closed Zone
3. Security Module Zone 3 - Motion Sensor configured as Single End-of-Line Resistor
4. Security Module Zone 4 - Motion Sensor configured as Double End-of-Line Resistor Zone
5. Security Module Zone 5 - Flood Sensor configured as Normally Closed Zone
6. Security Module Zone 6 - Flood Sensor configured as Normally Closed Zone

Note: In Security Module Zone settings ("Configuration" tab) it is necessary to select appropriate Zone Wiring according to the physical installation and setting you have done on your side for the individual sensor. On how to connect individual sensors / devices appropriately and configure them as Normally Closed, Single End-of-Line Resistor or Double End-of-Line Resistor Zone, please check manufacturers manual and Zipato's Security Module manual. Not selecting appropriate Zone Wiring and not connecting the sensor appropriately could result with unwanted results and even malfunction of Zipabox Security Module and connected sensors/devices.

結果 (中文) 1:

在本教程中，它是解释了如何添加和配置 6 x 有线区 ︰1.安全模块区 1-门传感器配置为通常封闭区2.安全模块区 2-窗口传感器配置为通常封闭区3.安全模块区 3-运动传感器配置为单个行尾电阻4.安全模块区 4-运动传感器配置为双行尾电阻区5.安全模块区 5-洪水传感器配置为通常封闭区6.安全模块区 6-洪水传感器配置为通常封闭区注 ︰ 安全模块区域中设置 （"配置"选项卡） 是必要的选择适当区域布线的物理安装和设置，您已经在你这一边为单独的传感器。有关如何连接各个传感器 / 设备适当并将它们配置为常闭、 单行尾电阻或双端的线电阻区，请检查制造商手册和 Zipato 的安全模块手册。不选择适当的区域布线和不适当连接传感器可能会导致意外的结果与 Zipabox 安全模块和连接的传感器设备甚至是故障。

結果 (中文) 3:

在本教程中，它解释了如何添加和配置6个有线区域：1。安全模块区1门传感器配置为常闭区2。安全模块区2 -窗口传感器配置为常闭区3。安全模块区3 -运动传感器配置为单端的线电阻4。安全模块区4 -运动传感器配置为双端的线路电阻区5。安全模块区5 -洪水传感器配置为常闭区6。安全模块区6 -洪水传感器配置为常闭区注意：在安全模块区域设置（“配置”选项卡），它是必要的选择适当的区域布线，根据物理安装和设置您已经做了您的个人传感器的一侧。如何适当地连接各个传感器/设备和配置为常闭，线路电阻或线电阻带双端单端，请生产厂家的说明书和zipato安全模块手册。没有选择合适的区域布线和连接的传感器可能会导致意想不到的结果，适当的zipabox安全模块甚至故障和连接的传感器/设备。