一、概述本系列高压电动机适用于海拔不超过1000m， 环境温度低于40

一、概述
本系列高压电动机适用于海拔不超过1000m， 环境温度低于40℃，少灰尘，无蒸气、酸、碱等腐蚀性气体的室内环境。
该系列高压电动机额定电压为6000V或10000V，允许电压的偏差范围为±5%，电源的额定频率为50Hz，额定功率因数为0.9（超前）。
电动机有一个圆柱形轴伸端，电动机的旋转方向应与指向牌上规定的方向一致，旋转方向由集电环一侧看一般为逆时针；
该系列高压电动机主要用于驱动各种矿山磨机等机械，用联轴器连接时轴伸上不得有除去联轴器重量以外的外加轴向和径向力。
该同步电动机励磁系统采用可控硅励磁装置。该电机允许全压直接起动，当电网容量不允许全压起动时，也可降压起动，此时，电动机的起动电流和端电压成正比下降，而起动转矩与端电压的平方成正比下降。
采用座式轴承，有油环式和复合式两种，座式轴承与安装底板间设有绝缘衬板，以防止轴电流的产生。
二、结构简介
TDMK（TM）矿山磨机用大型交流三相同步电动机，机座为钢板焊接结构，带底架；防护等级IP00，冷却方式IC01，安装型式IM7311或不带转轴和座式轴承的IM5710，定额类型S1，定子绕组接线方法Y接，绝缘等级F（按B级考核）。
定子采用0.5毫米厚的低损耗硅钢薄板冲制的扇形片叠压而成，铁芯上有定向通风槽孔，定子绕组采用成型的双迭短矩线圈，绝缘等级为F级；
转子磁极采用钢板冲制而成，与磁极线圈一同装在转子磁轭上，磁极线圈F极绝缘，当用户采用气动离合器时，可按用户要求设计转轴或轴打孔。
三、用途
本系列电动机主要用于传动矿山磨机，主要作为格子型球磨机、棒磨机、磨煤机的原动机。

結果 (英文) 1:

I. Overview
This series of high-voltage motors are suitable for altitude does not exceed 1000m, ambient temperature is below 40 ℃, less dust, vapors, acids, alkalis and other corrosive gases in the indoor environment.
The series of high-voltage motors rated voltage 6000v or 10000v, allowable voltage variation range of ± 5%, power rated frequency 50hz, rated power factor of 0.9 (advanced).
Motor having a cylindrical shaft end, the rotation direction of the motor on the card should be provided with the point in the same direction, the direction of rotation side of the collector ring see generally counterclockwise;
This series is mainly used for high-voltage motors driving various mining mill and other machinery,Connection with the coupling shaft extension may not have to remove the coupling weight than external axial and radial forces.
The synchronous motor excitation system using SCR excitation device. Full voltage of the motor allows the direct starting, when the grid capacity not full pressure start, they can start down this time, the motor terminal voltage is proportional to the starting current and drop, and the starting torque and voltage drop proportional to the square .
Adopt pedestal bearing with oil ring and composite type two, pedestal mounting plate between the bearing and an insulating liner to prevent shaft current generation.
Second, the structural profile
tdmk (tm) Mine mill with a large three-phase AC synchronous motor,Base for the steel plate welded structure, with a chassis; protection class ip00, cooling ic01, Mounting im7311 or without shaft and pedestal bearings im5710, fixed type s1, y connected stator winding wiring, insulation class f (press b level examination).
A stator with 0.5 mm thick low-loss silicon steel sheet punching fan-shaped pieces made of laminated iron core has directed the ventilation slots of the stator windings are double stacked short moments forming coil insulation class f-level;
rotor pole steel plate punching, together with the magnetic coil mounted on the rotor yoke, f pole pole coil insulation, when the user uses pneumatic clutch,According to user requirements and design the shaft or shaft drilling.
Third, use
This series motor is mainly used for transmission mine mill, primarily as a lattice-type ball mill, rod mill, mill prime mover.

結果 (英文) 2:

A summary of the series of high-voltage motors,
for altitude does not exceed 1000m, the environment temperature is below 40 ℃, less dust, no steam, acid, alkali and other corrosive gases indoor environment.
the series high voltage motor for rated voltage of 6000V or 10000V, allowable error voltage of ± 5%, rated power supply frequency is 50Hz, rated power factor is 0.9 (lead).
motor has a cylindrical shaft extension end, the rotation direction of the motor should be stipulated and pointing to the board of the direction, the direction of rotation by the collector ring side generally anticlockwise;
the series of high-voltage motors are mainly used to drive a variety of mine mill machinery,Coupling connection shaft extension may not have to remove the coupling weight outside of the external axial and radial force.
the synchronous motor excitation system with controllable silicon excitation device. The motor to allow direct starting pressure, when the power grid capacity does not allow full voltage starting, can also be reduced voltage starting, at this time, the starting current of the motor and the end is directly proportional to the voltage drop, and the starting torque and the terminal voltage is proportional to the square of the fall.
the pedestal bearing, oil ring type and combined type two kinds, insulating lining plate is provided with a seat type bearing and the mounting plate, to prevent the shaft current.
two, structure of
TDMK (TM) large AC three-phase synchronous motor for mine mill,The base for the steel plate welded structure, with the chassis; the level of protection IP00, cooling mode IC01, mounting type IM7311 or without the shaft and the bearing pedestal IM5710, quota type S1, stator winding wiring method Y, insulation class F (assessment according to B grade). 0.5 mm thick low loss silicon steel sheet sector laminations of pressure by
stator, directional ventilation slot iron core, stator winding adopts forming double overlapping short rectangular coil, the insulation class is F;
rotor pole with steel plate punching, and pole coil are mounted on the rotor magnet yoke, pole coil F pole insulation, when the user adopts pneumatic clutch,According to the design of the shaft or shaft drilling user requirements.
three
, use this series motors is mainly used for transmission of mine mill, mainly as a prime mover of lattice type ball mill, rod mill, coal mill.

結果 (英文) 3:

Overview
high voltage motors in this series applies to the altitude does not exceed 1000m, the ambient temperature is below 40 ° c, less dust, no steam, acids, alkalis and other corrosive gas indoor environment.
The series high voltage motor rated voltage is 6000V, 10000V, allowed deviation of the voltage range is ± 5%, rated frequency power 50Hz, rated power factor 0.9 (Advanced).
Has a cylindrical shaft end of the motor, the direction of rotation of the motor should be in line with links to provisions on licensing, direction of rotation by slip rings on one side for the counterclockwise;
high voltage motors of the series is mainly used to drive various mine mill machinery,When connected with the coupling on the shaft must not remove coupling outside the weight of external axial and radial forces.
The use of SCR excitation system for synchronous motor exciter. The motor allows direct start, when the power grid capacity does not allow full pressure when starting, or voltage-reduced starting, at this time, the starting current of the motor and the voltage is proportional to the decline, and the torque is proportional to the square of the voltage drop.
Block, bearings, oil ring type and compound type two, bearings and installation backplane equipped with insulated liner to prevent shaft current.
Second, structure
TDMK (TM) mine mill large AC three-phase synchronous motor,Base for steel plate welded construction, with base; protection degree IP00 cooling IC01, mounting types IM7311 or without shaft and bearings of IM5710, fixed type S1, y stator winding connection method, insulation class f (b-class assessment).
Stator used 0.5 mm thick of low loss silicon steel sheet rushed system of fan tablets stacks pressure and into, iron core Shang has directed ventilation slot hole, stator winding used forming of double Diego short moments coil, insulated level for f level;
rotor pole used plate rushed system and into, and pole coil together loaded in rotor magnetic yoke Shang, pole coil f very insulated, dang user used pneumatic clutch Manager Shi,Users can request design shaft or shaft drilling. Three, use

mine mill Motors of this series are mainly used for transmission, mainly as a lattice-type ball Mills, Rod Mills, mill's original motivation.