Problem L
Swap Space
Time limit: 6 seconds
You administer a large cluster of computers with hard drives that use various file system types to store
data. You recently decided to unify the file systems to the same type. That is quite a challenge since all
the drives are currently in use, all of them are filled with important data to the limits of their capacities,
and you cannot afford to lose any of the data. Moreover, reformatting a drive to use a new file system
may significantly change the drive’s capacity. To make the reformat possible, you will have to buy an
extra hard drive. Obviously, you want to save money by minimizing the size of such extra storage.
You can reformat the drives in any order. Prior to reformatting a drive, you must move all data from that
drive to one or more other drives, splitting the data if necessary. After a drive is reformatted, you can
immediately start using it to store data from other drives. It is not necessary to put all the data on the
same drives they originally started on – in fact, this might even be impossible if some of the drives have
smaller capacity with the new file system. It is also allowed for some data to end up on the extra drive.
As an example, suppose you have four drives A, B, C, and D with drive capacities 6, 1, 3, and 3 GB.
Under the new file system, the capacities become 6, 7, 5, and 5 GB, respectively. If you buy only 1 GB
of extra space, you can move the data from drive B there and then reformat drive B. Now you have 7
GB free on drive B, so you can move the 6 GB from drive A there and reformat drive A. Finally, you
move the six total gigabytes from drives C and D to drive A, and reformat C and D.
Input
The input begins with a line containing one integer n (1 ≤ n ≤ 106
), which is the number of drives in
your cluster. Following this are n lines, each describing a drive as two integers a and b, where a is the
capacity with the old file system and b is the capacity with the new file system.
All capacities are given in gigabytes and satisfy 1 ≤ a, b ≤ 109
. (One thousand petabytes should be
enough for everyone, right?)
Output
Display the total extra capacity in gigabytes you must buy to reformat the drives.
Problem L
Swap Space
Time limit: 6 seconds
You administer a large cluster of computers with hard drives that use various file system types to store
data. You recently decided to unify the file systems to the same type. That is quite a challenge since all
the drives are currently in use, all of them are filled with important data to the limits of their capacities,
and you cannot afford to lose any of the data. Moreover, reformatting a drive to use a new file system
may significantly change the drive’s capacity. To make the reformat possible, you will have to buy an
extra hard drive. Obviously, you want to save money by minimizing the size of such extra storage.
You can reformat the drives in any order. Prior to reformatting a drive, you must move all data from that
drive to one or more other drives, splitting the data if necessary. After a drive is reformatted, you can
immediately start using it to store data from other drives. It is not necessary to put all the data on the
same drives they originally started on – in fact, this might even be impossible if some of the drives have
smaller capacity with the new file system. It is also allowed for some data to end up on the extra drive.
As an example, suppose you have four drives A, B, C, and D with drive capacities 6, 1, 3, and 3 GB.
Under the new file system, the capacities become 6, 7, 5, and 5 GB, respectively. If you buy only 1 GB
of extra space, you can move the data from drive B there and then reformat drive B. Now you have 7
GB free on drive B, so you can move the 6 GB from drive A there and reformat drive A. Finally, you
move the six total gigabytes from drives C and D to drive A, and reformat C and D.
Input
The input begins with a line containing one integer n (1 ≤ n ≤ 106
), which is the number of drives in
your cluster. Following this are n lines, each describing a drive as two integers a and b, where a is the
capacity with the old file system and b is the capacity with the new file system.
All capacities are given in gigabytes and satisfy 1 ≤ a, b ≤ 109
. (One thousand petabytes should be
enough for everyone, right?)
Output
Display the total extra capacity in gigabytes you must buy to reformat the drives.
正在翻譯中..