二.安装 动力可根据当地条件选用3.0KW(1500转/分)的电机或4

二.安装
动力可根据当地条件选用3.0KW(1500转/分)的电机或4至7马力的小型柴油机(转速调在2000至2200转/分)。动力的安装，电机可直接安装在电机板上，柴油机先安装在随机带的两条槽钢上，再根据现场情况进行固定，要考虑皮带张紧度的调整，柴油机支架要与本机机架焊接为一体.所需B型皮带现场选配。皮带轮罩根据现场情况自制。
三.调试
1.安装好机体和附件后,检查所有紧固螺钉或螺栓;
2.减速器加注40号机油(约500ml)，以在视油窗看到油即可；
3.滑块3的锁定螺钉要保证滑块在螺杆上自由滑动而不转动;
4.松开压轮，挂接皮带,进行空运转半小时.
四.运转
将压轮放松到最后,使出渣锥体退出,开动机器,倒入灭菌后的棕榈果,看到棕榈果顺畅的由出渣锥体排出,缓慢转动压轮使出渣锥体前进,逐步加大出渣锥体给筛笼内的棕榈果的压力,开始出油,出渣锥体同筛笼之间的距离以出渣顺畅,油渣含油率少到满意为准。根据出渣情况随时转动压论进行调节。柴油机的转速调到螺旋杆的转速25转/分左右为准。
五.注意事项
日检查紧固螺栓一次;
日观察减速器油面一次保证油面高度,新机器运转10日后放掉全部机油并用柴油冲洗，待干后加入新机油；以后每半年更换机油一次;
每次重新开机都要按”四.运转”所述进行,严禁压轮推动锥体快速前进;
在拆装榨螺杆时,先将“9.挡栓”全部退出，松开锁紧螺栓13,可借助压轮的前进慢慢的将榨螺拉出,装进榨螺时一定注意,不能用锤猛击,以免造成减速器损坏;

結果 (英文) 1:

2 Installation
power can be selected according to local conditions 3.0kw (1500 rev / min) of the motor or 4-7 horsepower small diesel engine (speed controller at 2000-2200 r / min). Power installation, the motor can be mounted directly on the motor plate, with the engine installed in a random two channel, and then is fixed according to the situation, to consider the adjustment of the belt tension, and the engine bracket to the unit frame welded into one. required b belts scene matching. Homemade pulley cover according to the scene.
Three. Debugging
1. Installed body and accessories, check all screws or bolts;
2. Reducer No. 40 oil filling (about 500ml),To see the sight glass oil can;
3 slider 3 locking screws to ensure that the slider does not slide freely on the screw rotation;
4. Loosen the pressure roller, articulated belts, air operation carried out for half an hour
IV. operating pressure wheel
will relax to the end, resorted to slag cone exit, start the machine, pour sterilized palm fruit, palm fruit to see smooth cone slag discharged by slowly turning the pressure roller slag cone forward, and gradually increase the slag cone sieve cage palm fruit to the pressure and began out of oil, slag cone sieve cage with the distance between the slag and smooth, to the satisfaction of diesel oil content less prevail. According to the dregs of pressed at any time to adjust the rotation.Engine speed adjusted auger speed 25 rev / min or so prevail.
V. Notes
fastening bolts checked once a day;
observe the gear unit oil once a day to ensure the oil level, the new machine is running 10 let go of all future oil and diesel rinse and dry after adding new oil; replaced every six months after Oil once;
every reboot should press the "four. operation" described prohibited roller cone push fast forward;
pressed in dismantling the screw, the first "9. retaining bolt" all out, release locking bolt 13 with the aid of roller forward slowly pull the pressing screw, put some attention when pressing screw can not be hit with a hammer to avoid damage to the gear unit;

結果 (英文) 2:

Two. Install
power can be selected according to the local conditions of 3.0KW (1500 rpm) small diesel motor or 4 to 7 horsepower engine (speed from 2000 to 2200 rpm). Power installation, the motor can be mounted directly on the motor plate, diesel machines installed in the two channel random band, then according to the situation of fixed, to consider the belt tension adjustment, diesel engine support to welding and the machine frame into a whole. The required B type belt site selection. Pulley cover made according to site conditions.
three
1. Debugging installation body and accessories, check all the fastening screws or bolts;
2. reducer with No. 40 oil (about 500ml),To see the oil in the oil window; the locking screw
3. block 3 to ensure the slider slides freely in the screw and does not rotate;
4. release the pressure wheel, hanging belt, idle for half an hour.
four. Operation
will press wheel to relax to finally, using slag cone exit, start the machine, poured into the after sterilization of the palm fruit, see palm fruit smooth by slag cone discharge, slowly rotating wheel with slag cone forward, gradually increase the cinder cone for the sieve cage palm fruit pressure, began to oil, slag cone with the distance between the sieve cage to slag is smooth, oil rate is less satisfactory as with oil. According to slag at any time adjust rotating pressure theory.Speed to the screw rod of the diesel engine speed of 25 rpm for.
five. Note
date check fastening bolt once;
day observation reducer oil face a guarantee oil surface height, the new machine working for 10 days let go of all oil and diesel oil to be dry after washing, adding new oil; every six months after the oil change at a time;
each reboot to "four." the operation, no pressure wheel drives the cone fast forward; in disassembly pressing screw, the first "9 retaining bolt" all withdraw, loosen the lock bolt 13, slowly will screw out by pressing wheel forward, into the screw must pay attention to, can not use the hammer blow, in order to avoid reducer damage;

結果 (英文) 3:

II. install 3.0KW
power according to the local conditions (1500 rpm) motor or small 4 to 7 horsepower diesel engine (speed adjustable in 2000 to 2,200 RPM). Power installed, the motor can be mounted directly on the motor plate, diesel engine installed in a random band on two channels, fixed according to the situation, taking into account the belt tension adjustment, diesel engine bracket to the machine frame welded as a whole. the b-type belt scene matching. Homemade pulley cover according to the scene.
III. debug
1. After you install the body and attachments, check all screws or bolts;
2. reducer raise 40th motor oil (500ml),To see oil in the oil window;
3. slider 3 locking screw to ensure the slider free sliding without turning on the screw;
4. release the pressure wheel, hook the belt, go by air for half an hour.
Four. running
will pressure round relax to last, resorted to slag cone exit, started machine, pour sterilization Hou of Palm fruit, see Palm fruit smooth of by out slag cone discharge, slow turned pressure round resorted to slag cone forward, gradually increased out slag cone to sieve cage within of Palm fruit of pressure, began out oil, out slag cone with sieve cage Zhijian of distance to out slag smooth, diesel containing oil rate less to satisfaction for associate. Adjusted according to the slag situation at any time turn on the.Diesel engine speed adjusting screw speed 25 rpm or so.
Five. attention matters
day check tight solid bolt once;
day observation reducer oil surface once guarantee oil surface height, new machine running 10th Hou put off all oil and diesel flush, stay dry Hou joined new oil; yihou each half replaced oil once;
every time again power on are to by "four. running" by in for, is strictly prohibited pressure round promote cone fast forward;
in disassembly and Assembly squeezed screw Rod Shi, first will "9. retaining tied" all exit, release lock tight bolt 13, can with pressure round of forward slowly of will squeezed screw pull, Put it in a press screw must be careful, you can't use the hammer blow, may damage the reducer;