致中壢廠A2W/B各位老闆，能否取消run/stopＸ2+L/HＸ3檢

致中壢廠A2W/B各位老闆，能否取消run/stopＸ2+L/HＸ3檢查白點及外腳有無偏移的操作流程?W/B操作人員檢查白點及外腳有無偏移是最根本的站別責任，事實上大多數OP不管是本籍或外籍都不明白一點得要求這個步驟的定義到底是為了什麼。檢查白點及外腳的方式並不是只有一種按壓L/H的操作方式，現在只是因為老闆有要求，OP必須遵守，然而大家往往都是用自己最習慣的方式或是機台最適合的方式，再去配合你們要求的操作手法，言簡意賅有偏移疑慮檢查N便都不成問題，無意義的Run/Stop和標的游移只會造成燈光更偏移，有時還得調整燈光亮度。舉例來說常常有材料和機台異常，小停機種類無限排列組合，每次光是要配合run/stopＸ2+L/HＸ3檢查白點及外腳於bond後兩分鐘內達成的標準，所消耗的心力和時間已經遠遠高過於原來需要解決的問題了。試問今天這樣的SOP，如果拿來要求Team/ME/PE能達到百分百PASS？會不會被笑淪為無稽之談？如果無法卻要求OP是否過於苛刻。試想這樣的要求到底是為了什麼?方便撈每一位OP有無確實做白點及外腳有無偏移的確認而定義的狹義規則嗎?當然我們都知道沒有人會希望有異常批的發生。

結果 (繁體中文) 2:

To all the bosses of Zhongli Factory A2W/B, can we cancel the operation process of checking for white spots and offset of the outer feet on run/stopX2+L/HX3? The fundamental responsibility of the W/B operator is to check for any deviation in the white spots and outer feet. In fact, most OPs, whether native or foreign, do not understand the purpose of this step. The way to check the white spots and outer feet is not just one way to press L/H, but now it is only because the boss has requirements that the OP must comply. However, everyone often uses their own most accustomed method or the most suitable method for the machine, and then cooperates with the operation method you require. It is concise and there are doubts about deviation. Checking N is not a problem, and meaningless Run/Stop and moving the target will only cause more deviation of the light, Sometimes it is necessary to adjust the brightness of the lights. For example, there are often material and machine abnormalities, and the types of small shutdowns are infinitely arranged and combined. Each time, it is necessary to cooperate with run/stopX2+L/HX3 to check the white spots and the standards reached by the outer feet within two minutes after the bond, which consumes much more effort and time than the original problem that needs to be solved. May I ask if today's SOP requires Team/ME/PE to achieve 100% PASS? Will laughter turn into nonsense? If unable, is the OP too demanding. What exactly is this requirement for? Is there a narrow rule defined to facilitate the confirmation of white spots and offset of the outer feet for each OP? Of course, we all know that no one would want abnormal batches to occur.

結果 (繁體中文) 3:

To the bosses of A2W/B of Zhongli Factory, can you cancel the operation flow of Run/Stop X2+L/HX3 to check whether the white point and outer foot are offset? It is the most fundamental duty of W/B operators to check whether the white point and outer foot are offset. In fact, most OPs, whether native or foreign, don't understand what the definition of this step is for. There is not only one way to check the white spots and outer feet by pressing L/H, but now it is only because the boss requires it, and the OP must abide by it. However, everyone often uses their most accustomed way or the most suitable way of the machine, and then cooperates with the operation methods you require. Simply speaking, it is not a problem to check N if there is any doubt about deviation. Meaningless Run/Stop and target wandering will only cause the lights to deviate more, and sometimes the brightness of the lights has to be adjusted. For example, there are often abnormal materials and machines, and the types of small downtime are infinitely arranged and combined. Every time, it is necessary to cooperate with Run/Stop X2+L/HX3 to check the white point and the standard reached by the outer foot within two minutes after bond, which consumes much more effort and time than the original problems that need to be solved. I would like to ask today's SOP, if it is used to require Team/ME/PE to achieve 100% PASS? Will it be reduced to nonsense by laughter? If not, is it too harsh to ask for OP? Imagine what such a request is for? Is it convenient to find out the narrow rules defined by whether each OP does confirm whether the white point and the outer foot are offset? Of course, we all know that no one wants an abnormal batch to happen.